6440A REV G Norge Washer Parts List

Bake element (element bake)

This partially open-style bake element comes with ¼-inch push-on terminals and is located on the bottom of the oven. This bake element provides heat for baking. If your oven is too hot, not heating evenly, the element is not heating, or has little to no heat when baking, you may need to replace your bake element. You can use a multi meter to test the bake element for electrical continuity to see if you need to replace it. This is a genuine OEM part. Please remember to disconnect the power to the range before starting your repair.

Lower rack assembly - grey (rack assy)

This part is a genuine OEM part. This white lower dish rack assembly comes with eight light-gray rollers for easy access. The dish rack is approximately 21 inches wide x 22 inches deep. The dish rack holds dishes in place during the dish washing cycle. If you see rust spots on the dishes, the lower rack will not pull out, or the lower rack is visibly rusted or damaged, you will need to replace the part. Other common symptoms include: unusual or loud noises coming from the unit, or the dishes on the lower rack not being washed properly.

M series new style coil kit (gas valve secondary coil)

This gas dryer ignition coil set comes with two ignition coils: one three-terminal boost/hold coil, and one two-terminal secondary coil. If there is no heat or your drying time is getting longer, the coils may be bad and will need to be replaced. Once the coils go bad they do not hold the gas valve open properly. Usually only one of them burns out but you should replace them as a set. Both must be operational for the gas valve to open. This is a genuine OEM part. Please remember to disconnect the power to your dryer before starting the repair.

Agitator repair kit (use wpl 285746)

This agitator repair kit is used to move the upper agitator and connects the base of the agitator with the agitator top mover. The kit is most commonly used if the top part of the agitator is not moving correctly but the bottom portion is. If your washer will not agitate or is noisy, you may need to replace the kit. The kit includes a medium cam, agitator dogs, bearing, thrust bearing washer, and a dust cap seal. Agitator grease is recommended for the repair, but it is not included with the agitator repair kit, it must be ordered separately. This is a genuine OEM part. Please remember to disconnect the power and water supply to the washer before starting your repair.

Rear drum support roller kit (support)

This drum support roller kit is used for square-ported model clothes dryers. It has a metallic bearing in its center. This support roller is used to hold the drum in place in the cabinet while letting the drum rotate on the support rollers. If your dryer is noisy, will not tumble, or takes too long to dry you might need to replace the roller. The kit is a genuine OEM kit and it includes two drum support rollers, four tri rings, and one retaining washer. It is recommended that you replace both rollers at once. Please remember to disconnect the power to your appliance before starting your repair.

D-shaped knob clip (clip knob)

This control knob clip helps secure the timer knob to the shaft allowing you to select the desired setting for your dryer. If the knob has become loose or the clip is missing you will need to replace the clip. This clip is a genuine OEM part, made of metal and is sold individually.

Meat drawer rail - right side (drawer support rail - right side)

This replacement drawer slide rail is for the right-hand side of your refrigerator. This part attaches to the inside wall of your refrigerator to support the sliding crisper drawer. If the rail is broken or the drawer is not sliding properly, you will need to replace the slide rail. You will need a Phillips screwdriver to complete this repair.

Control knob and clip - white (knob and clip asm)

This knob and clip set is an OEM replacement part for your washer or dryer. The knob accepts a D-shaped shaft and is sold individually.

Rear drum bearing kit (shaft)

This rear drum bearing kit includes one bearing, one ball shaft, one ball bearing, one ball bearing retainer, a small tube of high temperature lubricant, and installation screws. The support bearing helps support the dryer drum to rotate quietly and smoothly during operation. The bearing attaches on the inside of the rear panel of the dryer cabinet. Over time the drum bearing will wear out. This kit will help keep your dryer running as smoothly as possible with as little noise as possible. This is a genuine OEM part. Please remember to disconnect the power before starting your repair.

Front glide kit (sub 306508)

The front glide helps the drum rotate smoothly and quietly while operating. If your dryer will not tumble or is noisy, the glide could be worn down, causing a metal on metal noise, and will need to be replaced. It is recommended to replace both glides at the same time; a rivet tool is required for this installation. This kit includes a blue plastic glide, a brown cork pad, and two metallic rivets. The front drum glide kit is a genuine OEM part. Please remember to disconnect the power to the dryer before starting your repair.

Upper crisper drawer cover - glass not included (use 240350702)

This cover holds up the top crisper drawer, and has drawer glides molded in it. This upper crisper drawer cover is a manufacturer-approved replacement part for your refrigerator. It has drawer glides molded into the frame but this part does not include the glass cover. To replace this part, lift out the glass cover and snap out the drawer frame. Snap this new frame cover into place and replace the glass.

Pan slide track (track)

This pan slide track can be used for either the left or right side of the pan.

Crisper drawer cover (cover pan low)

This crisper drawer cover has the drawer slides built into it to allow the crisper drawer to slide in and out. This model measures 24 1/2 inches long x 19 inches wide x 2 5/8 inches deep, is made of plastic and is white in color. If the cover becomes cracked or damaged, you will need to replace it. This is a genuine OEM part.

Refrigerator ice and water filter (filter canister)

Replacement ice maker (refrigerator ice maker)

This 8-cube ice maker is used to help produce ice for your refrigerator. The ice maker receives water from the water inlet valve and will freeze the water until ice cubes are formed. Once the water has been frozen the ice cubes will be ejected from the mold into the ice bucket and will refill with water to repeat the process until the ice bucket is full. This ice maker does not include the bail or shut off arm. You can reuse the arms for your old ice maker or you can also order them separately if required. It does come complete with flat and round plug wiring harness, the mounting hardware, and the instructions. The harness can be reused. This ice maker will not fit refrigerators that have the ice auger mounted on the door. If your ice maker is not making ice you may need to replace this part. Please remember to disconnect the power and water supply before starting your repair. This ice maker is a genuine OEM part.